| | |
HDB Reg. Contractor HB-09-5474D
Work At HeightSingapore · operated by Ezzogenics
Looking up at finished ceiling and soffit surfaces around an opening
Article

Fire-Rated Ceiling Handover in Singapore

Trace one ceiling zone from the approved assembly through product certification, declaration, installation, QP supervision and project fire-safety status.

Flowchart in sequence: first, the approved assembly, recording the zone, drawing revision, required fire resistance and approved details; second, product evidence, matching the system to the applicable Certificate of Conformity and/or Declaration of Compliance; third, installation, tracing the work through FSC02 and installation and supervision records. Decision: has the QP resolved deviations and ratings? If no, hold until the QP resolves them. If yes, project status is checked separately: supervision records are reconciled, the project Fire Safety Certificate follows full completion of fire safety works, and a Temporary Fire Permit is a separate, limited arrangement.
Fire-safety handover flow: reconcile the approved assembly, applicable product evidence, installation records and QP supervision before checking project FSC/TFP status. A CoC alone does not prove correct installation or close-out. Swipe sideways to read it, or open the full-size flowchart.

Start with the approved assembly and exact location

Record floor, room or gridlines, drawing number and revision. Ask the QP to identify the required fire resistance and the approved assembly for that zone. Where the ceiling contributes to fire resistance, framing, panels, access hatches, joints, penetrations, services and interfaces may all matter. Fire Code clause 3.3 addresses fire resistance of elements of structure, including relevant suspended-ceiling arrangements. [1]

The Fire Safety Act addresses approval of plans of fire safety works, carrying out those works in accordance with approved plans, QP appointment and duties, and supervision. A substitution or site deviation therefore needs reconciliation through the project’s QP and approval process, not merely a supplier statement that a product has a rating. [2]

Match every record to its actual purpose

For regulated products and materials, Chapter 11 and Table 11A of the Fire Code set the relevant framework. A CoC is issued by an SAC-accredited certification body—not issued or endorsed by SCDF—and must match the actual product and certification scope. SCDF specifically identifies Declarations of Compliance for non-discrete systems such as fire-rated ceilings and fire-rated floors. Confirm which evidence applies to the installed system rather than asking only for ‘the certificate’. [3] [4]

FSC02 is listed by SCDF as the Regulated Fire Safety Products Installation Certificate. Use it with the applicable installation records and compare location, assembly and rating with the approved documents. Regulation 13 addresses the certificate of supervision on completion and proper records of reports, requests and correspondence. Keep those supervision and installation records traceable to the same ceiling zone. [5] [6]

Do not confuse product and installation evidence with project status

SCDF states that the project Fire Safety Certificate (FSC) is issued after full completion of all fire safety works. A Temporary Fire Permit (TFP) is a separate, limited arrangement where only very minor outstanding issues remain. Neither the product CoC nor FSC02 should be described as the project FSC. [7]

If a product description says one hour while an installation schedule says two hours for the same area, give the QP the exact page, revision, location and supporting evidence. Ask whether the approved requirement, product scope, record or installation needs clarification or correction. Retain the resolution for future ceiling openings, replacements and maintenance.

Related: see our height safety planning and method statements.

Read next: How to Sequence Ceiling Works When Several Contractors Share One Lift.

Practical checklist

  • Identify the approved assembly, drawing revision and ceiling zone.
  • Match CoC and/or Declaration of Compliance to the actual system and scope.
  • Link FSC02, installation evidence and QP supervision records to the same location.
  • Check project FSC or TFP status separately and reconcile contradictory ratings through the QP.

References

  1. Singapore Civil Defence Force. (2023). Fire Code 2023: Clause 3.3—Fire resistance of elements of structure.
  2. Fire Safety Act 1993 (Singapore), ss. 55–58. Singapore Statutes Online.
  3. Singapore Civil Defence Force. (2023). Fire Code 2023: Chapter 11, Table 11A—Regulated fire safety products and materials.
  4. Singapore Civil Defence Force. (n.d.). Regulated fire safety products.
  5. Singapore Civil Defence Force. (n.d.). Forms and guides.
  6. Fire Safety (Building and Pipeline Fire Safety) Regulations (Singapore), reg. 13. Singapore Statutes Online.
  7. Singapore Civil Defence Force. (n.d.). Fire Safety Certificate and Temporary Fire Permit.

Need help on the access side?

We can review your project, recommend an access method and provide method statements and rescue planning.

Contact us
Call